Suzhou Jidong New Material Technology Co., Ltd
Service Hotline:
0086 139 229 345 98
E-mail:13922934598@139.com
Online customer service
 Work Time
Mon to Fri :8:00-20:00
Sat to Sun :9:00-17:00
 Contact Details
手机:0086 139 229 345 98
邮箱:409639645@qq.com

The adjustment, measurement and control principle of CPP film process parameters are discussed

  124
Author:来源于绍兴博瑞Source:微信Link:https://mp.weixin.qq.com/s/8ds8rVNasPfghS1TFSR5rQ

I. Temperature monitoring and control


From the whole production process and production principle of cast film, we can know that the whole production of cast film is the change process of polymer aggregation state, which is closely related to the processing temperature of materials. For example, the surface temperature of the cooling roller is uniform and the temperature fluctuation is very small; the change and fluctuation of the extrusion temperature will cause the change of the film extrusion thickness and the change of the film performance. There are many temperature points that need to be controlled in the whole production line, so temperature control is the key point of casting film process control. Cast film temperature control point include:


  • Extruder temperature control area;

  • Temperature control area of screen changer;

  • Connect the temperature control area of the pipeline;

  • Temperature control area of die head;

  • Temperature control of cooling roller and post-cooling roller;

  • Temperature control of corona rod and corona cooling roller;

  • Air knife cooling and temperature control;

  • Cooling the feeding section of the extruder;

  • Cooling of reduction gearbox and motor.


1、Temperature detection


Because there are no special conditions such as ultra-high temperature, ultra-high pressure, ultra-low temperature, micro-pressure and corrosion resistance in the processing of cast film, ordinary temperature sensors can be used for temperature detection. Contact temperature sensors are divided into two categories.



Factors such as the temperature range of the heating zone, the accuracy of temperature control, and the service life and reliability of the measuring element must be considered in the selection of the temperature measuring element.


The time constant of the temperature measuring element is an important symbol of the temperature measuring element, which refers to the time required to reach 63.2% of the stable value of the measured medium from the beginning to the end of the measurement within the measuring range of the sensor. For the system with fast response, the sensor with small time constant should be selected; for the system with slow response, the sensor with large time constant should be selected. If the time constant is not properly selected, the temperature may be difficult to control, and even the system may oscillate.


2、Temperature control


二、Pressure measurement and control

In the casting film extrusion production line, the polymer is gradually plasticized, melted and mixed in the extruder due to the shearing of the screw and the heating of the barrel, and a certain pressure is generated. When the temperature of the extrusion system, the filter and the die head is fixed, and the opening of the die head and the filtering resistance are fixed, the flow of the extruded melt is proportional to the pressure of the extruder. Therefore, the extrusion pressure directly affects the extrusion thickness and thickness deviation of the film. Melt pressure detection and pressure control feedback systems are generally installed on cast film extrusion devices.


Melt pressure detection point:


  • Pressure detection before the filter screen of the extruder;

  • Pressure detection behind the filter screen of the extruder and in front of the metering pump (if any);

  • Pressure test after metering pump of extruder (if any);

  • Pressure test before fine filtration of extruder (if any);

  • Pressure detection at die inlet (can be omitted).


Other pressure monitoring points:


  • Air knife inner cavity air pressure detection;

  • Vacuum chamber air pressure detection;

  • Detection of each air pressure contact during equipment operation;

  • Water pressure test of waterway.


1、Pressure detection


Generally, for the co-extrusion film production line, each co-extrusion extruder is equipped with two pressure detection points, one is at the outlet of the extruder (in front of the filter screen), and the other is at the inlet of the die head (behind the filter screen).


2、Pressure sensing element

       

Pressure detection elements can be divided into two types: mechanical and electrical. Electrical pressure sensors can be divided into capacitive pressure sensors, piezoresistive pressure sensors and piezoelectric pressure sensors.

Piezoresistive pressure sensor (strain pressure sensor) is generally used in the production line of cast film, and its piezoresistance changes with the change of stress.



三、Speed control


In the extrusion drive and film transmission of the casting film production line, DC speed regulation was used at the earliest stage. With the development of frequency conversion speed regulation, in addition to the extrusion drive using DC speed regulation, the general film drive uses frequency conversion speed regulation or even servo drive system. Compared with DC speed regulation, the frequency conversion speed regulation device has many advantages: the frequency conversion speed regulation motor has no carbon brush, Cleaning and maintenance work does not exist, the reliability and the service life of the system can be improved, and the variable frequency speed regulation motor has high speed regulation efficiency and is more energy-saving.


The speed control includes the speed control of the extruder, the speed control of the metering pump, the speed control of the cooling roller, the speed control of the traction part and the speed control of the winder.


四、Measurement and control of thickness


The uniformity of film thickness is a very important quality index of cast film. In the high-speed automatic production line, the detection of film thickness uses high-precision, non-contact thickness gauge and feedback system for automatic detection and control.


1、Sensor for film thickness measurement


The most common is the radioisotope thickness gauge. The main radioisotopes are: Sr — 90ß ray, Kr — 85ß ray, Pm — 147ß ray, X-ray sensor, infrared sensor, etc.


The selection of the thickness gauge sensor is closely related to the basis weight of the film. In general, the Pm-147ß ray is suitable for measuring the film of 2-200 G/m2, and the Kr-85ß ray is suitable for measuring the plastic film of 10-2000 G/m2. The measurement of film thickness by radioactive source is based on the fact that when the ray enters the film to be measured, part of the ray will penetrate the film and the other part will be absorbed by the film. After the ray passes through the film, it will inevitably cause intensity attenuation. The thickness of the film can be calculated by detecting the proportion of attenuation. The schematic diagram is as follows:

2、Film Control of thickness


In the production of cast film, the transverse thickness uniformity of the film is generally controlled by adjusting the flow rate of the polymer melt by adjusting the gap of the die lip.


There are several ways to adjust the die lip gap:


  • Manually adjusting the clearance of the die lip is an economical, simple, practical and effective way to adjust the film thickness. Through the film thickness deviation displayed by the film thickness gauge, the gap of the die lip is adjusted by human behavior.

  • The method of automatic bolt adjustment is to adjust the power or temperature of the heating element on the thermal expansion bolt from the die lip, so that the bolt can be extended when the temperature rises or shortened when the temperature drops, so as to achieve the purpose of adjusting the opening of the die lip. The heating control mode is also divided into two types: temperature control or heating percentage control.

  • The equipment controlled by stepper motor is complex and bulky. However, the time period is adjusted, the response speed is fast, and the opening of the die lip can be adjusted in a wide range.


Thickness measurement and feedback:


  • In addition to the change of transverse thickness, the longitudinal thickness of the film is also changing in the production process. Therefore, the thickness measured by the thickness gauge each time includes the change of the film thickness in the cross section and the change of the film thickness in the longitudinal direction.

  • In the production process, the transverse thickness deviation of the film is adjusted by adjusting the opening of the die lip through the thermal expansion bolt, and the longitudinal thickness deviation is adjusted by adjusting the speed of the cooling roller or the speed of the extruder.

  • For the high-speed film production line, in order to reduce the longitudinal thickness deviation of the film as much as possible, there are two ways: improving the response speed of the sensor to improve the scanning speed; the other way is to use the average value of the longitudinal deviation of multiple scans as the basis of the longitudinal thickness deviation.



五、Control and measurement of tension


After the film enters the winder, the winding speed depends on the tension controller to compensate the tension and adjust the winding speed. There are two kinds of tension sensors: one is the floating roll tension sensor (or low friction cylinder); the other is the pressure strain tension sensor.


1、Floating roll tension sensor


The pressure of the film on the floating roller is converted into a voltage change signal by using the lever principle to control the winding speed of the film and ensure the constant winding tension.

2. Strain gauge tension sensor


In this system, the strain gauge pressure sensor converts the tension on the roller into a voltage signal to control the winding tension of the film and ensure that the winding tension is constant.


Because this kind of tension sensor precision is very high, therefore the control precision is also very high, the tension size may realize the stepless speed regulation, the operation is very convenient. The strain gauge tension sensor only depends on the result of tension detection to adjust the tension, which does not cause the change of film length.


In the process of increasing or decreasing the speed of the production line, the strain tension sensor can also adjust the tension quickly, stably and accurately, so as to avoid the deformation of the film in the process of increasing or decreasing the speed.




六、Measurement and control of material level:


In general, the structure of the casting film is A/B/C three layers produced according to the proportion of 20%/60%/20%. In the production process of the casting film, no matter which feed hopper is short of material, the layer structure of the film will be changed and the thickness of the film will change dramatically, resulting in unqualified defective products and waste products.


Because the rotation of the screw in the barrel depends on the back pressure of the raw material and the plastic melt to automatically find the center point, if the screw idles, it may cause the barrel to be swept by the screw. Therefore, the material level sensor should be installed on the feed hopper of the extruder to avoid the phenomenon of screw shortage.


                                                                             

一、Temperature monitoring and control


From the whole production process and production principle of cast film, we can know that the whole production of cast film is the change process of polymer aggregation state, which is closely related to the processing temperature of materials. For example, the surface temperature of the cooling roller is uniform and the temperature fluctuation is very small; the change and fluctuation of the extrusion temperature will cause the change of the film extrusion thickness and the change of the film performance. There are many temperature points that need to be controlled in the whole production line, so temperature control is the key point of casting film process control. Cast film temperature control point include:


  • Connect the temperature control area of the pipeline;   
  • Temperature control area of die head;   

  • Temperature control of cooling roller and post-cooling roller;   

  • Temperature control of corona roller and corona cooling roller;

  • Air knife cooling and temperature control;   

  • Cooling the feeding section of the extruder;   

  • Cooling of reduction gearbox and motor.   



1、Temperature detection


Because there are no special conditions such as ultra-high temperature, ultra-high pressure, ultra-low temperature, micro-pressure and corrosion resistance in the processing of cast film, ordinary temperature sensors can be used for temperature detection. Contact temperature sensors are divided into two categories.  

  Factors such as the temperature range of the heating zone, the accuracy of temperature control, and the service life and reliability of the measuring element must be considered in the selection of the temperature measuring element.   

The time constant of the temperature measuring element is an important symbol of the temperature measuring element, which refers to the time required to reach 63.2% of the stable value of the measured medium from the beginning to the end of the measurement within the measuring range of the sensor. For the system with fast response, the sensor with small time constant should be selected; for the system with slow response, the sensor with large time constant should be selected. If the time constant is not properly selected, the temperature may be difficult to control, and even the system may oscillate.   


2、Temperature control


二、Pressure measurement and control

In the casting film extrusion production line, the polymer is gradually plasticized, melted and mixed in the extruder due to the shearing of the screw and the heating of the barrel, and a certain pressure is generated. When the temperature of the extrusion system, the filter and the die head is fixed, and the opening of the die head and the filtering resistance are fixed, the flow of the extruded melt is proportional to the pressure of the extruder. Therefore, the extrusion pressure directly affects the extrusion thickness and thickness deviation of the film. Melt pressure detection and pressure control feedback systems are generally installed on cast film extrusion devices.


Melt pressure detection point:


  • Pressure detection before the filter screen of the extruder;
  • Pressure detection behind the filter screen of the extruder and in front of the metering pump (if any);   

  • Pressure test after metering pump of extruder (if any);   

  • Pressure test before fine filtration of extruder (if any);   

  • Pressure detection at die inlet (can be omitted).   


Other pressure monitoring points:


  • Air knife inner cavity air pressure detection;   
  • Vacuum chamber air pressure detection;   

  • Detection of each air pressure contact during equipment operation;   

  • Water pressure test of waterway.   


1、Pressure detection


Generally, for the co-extrusion film production line, each co-extrusion extruder is equipped with two pressure detection points, one is at the outlet of the extruder (in front of the filter screen), and the other is at the inlet of the die head (behind the filter screen).


2、Pressure detection element

       

Pressure detection elements can be divided into two types: mechanical and electrical. Electrical pressure sensors can be divided into capacitive pressure sensors, piezoresistive pressure sensors and piezoelectric pressure sensors.

Piezoresistive pressure sensor (strain pressure sensor) is generally used in the production line of cast film, and its piezoresistance changes with the change of stress.


三、Speed control


In the extrusion drive and film transmission of the casting film production line, DC speed regulation was used at the earliest stage. With the development of frequency conversion speed regulation, in addition to the extrusion drive using DC speed regulation, the general film drive uses frequency conversion speed regulation or even servo drive system. Compared with DC speed regulation, the frequency conversion speed regulation device has many advantages: the frequency conversion speed regulation motor has no carbon brush, Cleaning and maintenance work does not exist, the reliability and the service life of the system can be improved, and the variable frequency speed regulation motor has high speed regulation efficiency and is more energy-saving.


The speed control includes the speed control of the extruder, the speed control of the metering pump, the speed control of the cooling roll, the speed control of the traction part and the speed control of the winder.


四、Measurement and control of thickness


The uniformity of film thickness is a very important quality index of cast film. In the high-speed automatic production line, the detection of film thickness uses high-precision, non-contact thickness gauge and feedback system for automatic detection and control.


1、Sensor for film thickness measurement


The most common is the radioisotope thickness gauge. The main radioisotopes are: Sr — 90ß ray, Kr — 85ß ray, Pm — 147ß ray, X-ray sensor, infrared sensor, etc.


The selection of the thickness gauge sensor is closely related to the basis weight of the film. In general, the Pm-147ß ray is suitable for measuring the film of 2-200 G/㎡, and the Kr-85ß ray is suitable for measuring the plastic film of 10-2000 G/㎡. The measurement of film thickness by radioactive source is based on the fact that when the ray enters the film to be measured, part of the ray will penetrate the film and the other part will be absorbed by the film. After the ray passes through the film, it will inevitably cause intensity attenuation. The thickness of the film can be calculated by detecting the proportion of attenuation. The schematic diagram is as follows:

2、Film Control of thickness


In the production of cast film, the transverse thickness uniformity of the film is generally controlled by adjusting the flow rate of the polymer melt by adjusting the gap of the die lip.


There are several ways to adjust the die lip gap:


  • Manually adjusting the clearance of the die lip is an economical, simple, practical and effective way to adjust the film thickness. Through the film thickness deviation displayed by the film thickness gauge, the gap of the die lip is adjusted by human behavior.   
  • The method of automatic bolt adjustment is to adjust the power or temperature of the heating element on the thermal expansion bolt from the die lip, so that the bolt can be extended when the temperature rises or shortened when the temperature drops, so as to achieve the purpose of adjusting the opening of the die lip. The heating control mode is also divided into two types: temperature control or heating percentage control.   

  • The equipment controlled by stepper motor is complex and bulky. However, the time period is adjusted, the response speed is fast, and the opening of the die lip can be adjusted in a wide range.   



Thickness measurement and feedback:


  • In addition to the change of transverse thickness, the longitudinal thickness of the film is also changing in the production process. Therefore, the thickness measured by the thickness gauge each time includes the change of the film thickness in the cross section and the change of the film thickness in the longitudinal direction.   
  • In the production process, the transverse thickness deviation of the film is adjusted by adjusting the opening of the die lip through the thermal expansion bolt, and the longitudinal thickness deviation is adjusted by adjusting the speed of the cooling roller or the speed of the extruder.   

  • For the high-speed film production line, in order to reduce the longitudinal thickness deviation of the film as much as possible, there are two ways: improving the response speed of the sensor to improve the scanning speed; the other way is to use the average value of the longitudinal deviation of multiple scans as the basis of the longitudinal thickness deviation.   


五、Control and measurement of tension


After the film enters the winder, the winding speed depends on the tension controller to compensate the tension and adjust the winding speed. There are two kinds of tension sensors: one is the floating roll tension sensor (or low friction cylinder); the other is the pressure strain tension sensor.


1、Floating roll tension sensor


The pressure of the film on the floating roller is converted into a voltage change signal by using the lever principle to control the winding speed of the film and ensure that the winding tension is constant。

2、Strain gauge tension transducer


In this system, the strain gauge pressure sensor converts the tension on the roller into a voltage signal to control the winding tension of the film and ensure that the winding tension is constant.


Because this kind of tension sensor precision is very high, therefore the control precision is also very high, the tension size may realize the stepless speed regulation, the operation is very convenient. The strain gauge tension sensor only depends on the result of tension detection to adjust the tension, which does not cause the change of film length.


In the process of increasing or decreasing the speed of the production line, the strain tension sensor can also adjust the tension quickly, stably and accurately, so as to avoid the deformation of the film in the process of increasing or decreasing the speed.



六、Measurement and control of material level:


In general, the structure of the casting film is A/B/C three layers produced according to the proportion of 20%/60%/20%. In the production process of the casting film, no matter which feed hopper is short of material, the layer structure of the film will be changed and the thickness of the film will change dramatically, resulting in unqualified defective products and waste products.


Because the rotation of the screw in the barrel depends on the back pressure of the raw material and the plastic melt to automatically find the center point, if the screw idles, it may cause the barrel to be swept by the screw. Therefore, the material level sensor should be installed on the feed hopper of the extruder to avoid the phenomenon of screw shortage.



                                                                            来源于绍兴博瑞